Marley Power PE Duct (Continuous)

Accepted by major power authorities to house and protect power cables

Typically used with directional drilling / trenchless installations

  • Category A Underground Wiring Systems with Heavy Duty rated ducting recommended
  • Additional mechanical protection not practical with trenchless installations

 

High quality polyethylene (PE) material manufactured to AS/NZS 4130 dimensions

Marley Electrofusion & Compression Fittings recommended

Why Marley?

Quality Assurance
Practices & procedures to deliver on customer expectations

Proven Reliability
History of durability in NZ conditions

Recyclable
100% recyclable uPVC and PE materials

Certification
Made to NZ standards & specifications

Full Range
Conduit & cable duct systems for building & infrastructure applications

Support
Nationwide sales and technical support

Components

  PRODUCTS

Power PE Duct (Subduct)

Power PE Duct

Electrofusion Coupler PE Joiner

Electrofusion Slide Coupler

Resources

Technical Details

SIZE4  
DIAMETER (mm) 20, 25, 32, 40, 50, 63, 90, 110, 125, 140, 160
LENGTH (m) 12, 50, 100, 150, 200, 500, 1000 (coil)

MATERIAL
COLOUR1 Orange, Green, Red, Salmon
FORMULATION Polyethylene
FINISH Matte Finish

TEMPERATURE
SERVICE TEMPERATURE RANGE 0˚C to 60˚C
LINEAR CO EFFICIENT OF THERMAL EXPANSION 17 x 10-5 m/(mK)

FITTINGS
MARLEY COLOUR MATCH1
EXTENSIVE RANGE
JOINT Electrofusion/compression
DUTY RATING2 SDR11-SDR17

DURABILITY
BUILDING CODE NZBC B2
(Interior or concealed applications)
DUTY RATING2 Heavy Duty
Medium Duty
COMPRESSION RESISTANCE HD
MD
IMPACT RESISTANCE HD
MD
RESISTANCE TO BURNING Non flame propagating
UV RESISTANCE N/A
CHEMICAL RESISTANCE High3

COMPLIANCE
MANUFACTURING STANDARD AS/NZS 4130
ENVIRONMENTAL ACCREDITATION BEP Certified – NA
ISO 14001

  1. Both rigid and continuous cable duct are available in custom colours. Minimum order quantities and lead time apply
  2. Duty rating varies on size and customer requirements, please contact Marley for more information
  3. Avoid contact with ketones, esters, aromatic and chlorinated solvent
  4. Not all sizes available – refer to Price Book for specific product category sizing

TOWING LOADS

Continuous duct is predominantly installed using ‘no dig’ methods which require the duct to be pulled through the ground. This requires a pulling load to be applied to the duct in order to draw it forward and the load requirement will be influenced by; the length and straightness of the run, the friction between the pipe, and the surrounding ground and diameter of the pipe.

Where possible, the minimum towing load to achieve the installation should be used and in no case should the loads in the following table be exceeded. Exceeding these loads may result in a reduction of the diameter and wall thickness of the duct.

When slip lining it is recommended that for long strings, a pipe relaxation period of at least 24 hours is allowed before grouting or making permanent tie-in joints.

Where a pipe of a greater wall thickness (lower SDR) is being used to those shown in the table then he same guidelines can safely be used.

MARLEY PIPE SIZE AND TOWING LOADS

PIPE SIZE SDR 20°C Tonnes
20 11 0.08*
25 11 0.12*
32 13.6 0.27*
40 17 0.22
50 17 0.32
63 17 0.5
90 17 1.1
110 17 1.6
125 17 2.1
140 17 2.5
160 17 3.4

* It is recommended that the smaller diameters be pulled by hand.

* Provided permission by Standards New Zealand under license 001143.

The above information is provided permission by Standards New Zealand under license 001143.

The Ultimate Defence

Using an application-based approach, the Marley ARMA® range is simplified to save space in your vehicle and time at the work site, while achieving a long lasting, professional finish each and every time.

Independently verified to comply with AS/NZS 61386, the Marley ARMA® rigid conduit system is proudly made in New Zealand and 100% recyclable.

View